10 Ohm, Lead free, carbon film, through-hole resistor. Used when fine tuning many RGH/JTAG installs.
Resistance: 10 Ohms
Power (Watts): 0.25W, 1/4W
Composition: Carbon Film
Temperature Coefficient: 350ppm/Celcius
Tolerance: +/- 5%
Size: 0.094" Dia x 0.248" L (2.40mm x 6.30mm)
Number of Terminations: 2
Verbatim (94934) LightScribe CD-R 52X Blank CDR Media Discs 80Min/700MB in 10 Pack Cake Box
Bring your controller back to 100% performance with these brand new replacement analog thumbsticks with D-pad for your Xbox 360 controller. Color match your painted controller or just add them for extra bling.
Fits both wired and wireless Xbox 360 controllers. Even fits original Xbox controllers.
Note: Torx 8 Security and Phillips Screwdriver required for controller installation.
This is the wires install cable for the NAND-X or JR Programmer
Simply solder the wires to the correct points on the motherboard and plug into the NAND-X or JR Programmer. Easy !
This is the JTAG QSB kit that is included with the NAND-X. Known as Kit #2, this kit installs to the top of the motherboard and to the front ROL (Ring of Light) panel.
Works with all non-Xenon motherboards (Falcon, Zephyr, Opus, Jasper). Can be used with the R-JTAG install as an alternative to the #5 JTAG KIT.
Installation Guide: CLICK HERE
Other JTAG Instructions & Guides: CLICK HERE
This device is designed primarily to aid or assist in the repair or replacement of defective hardware and also for the use of and development of legal open source software. It does not enable any kind of piracy or have any code or any kind of microchip whatsoever that circumvents any kind of protection. It is a basic circuit of wires and diodes that is all. We do not support nor encourage, if possible, potential infringements of others intellectual property rights - please do not contact us with any question related to this use as we will not respond. DO NOT use or buy this product if you are looking to perform any illegal activity.
The TX SPUTNIK360 - LITEON DG-16D4S DVD UNLOCK SWITCH is a simple device that disables the write protect on any Liteon DG-16D4S drive that has the MXIC SPI flash device so you can easily repair or replace your faulty DVD drive with this model and have the ability to program your consoles DVD key.
Yet another simple and useful device from Team Xecuter.
Improve your RGH boot times with this professionally manufactured Double Shielded 50Ohm grounded cable for the CPU_RST point.
It has a pre-grounded wire that is soldered to the main shield and also has both ends cut, stripped and heatshrink wrapped.
The length is perfect for Slim installs and the bottom CPU_RST point (the Slim POST QSB is Recommended)
Shielded Cable Specs:
The new CR3 PRO is aimed at users who demand the highest RGH performance possible and the ability to tune their settings to an extreme level.
The CR3 PRO is not for beginners, modders looking for cheap and cheerful solutions or anyone who is happy with slow, unreliable glitching. There are other devices out there that claim to be as good and with their own version of RATER but don't believe the hype. Without a 150Mhz RER crystal you are not going to get any where near the performance levels that the CR3 Pro gives you. This is the fastest and most configurable RGH device on the market.
This version of CR3 PRO is designed for slims that have had POST removed - so is developed with new code to support FAKE POST (Corona v3, Corona v4, Corona v5 & Corona v6). If you have a Trinity, Corona v1 or Corona v2 you will need the CR3 PRO FULL POST version.
Xecuter CR3 PRO v1.0S FAKE POST Features:
The CR3 Pro Ultimate Kit Includes:
FAKE POST Supported Motherboards (Click here for identification guide):
Note: To install to a Corona with POST removed one of the pins under the CPU needs to be accessed. This can be done with a degree of difficulty (see here), but Xecuter have designed a tool that can achieve this with ease - the POSTFIX ADAPTER V2 (now includes varied lengths for POST_OUT 5/50/70/90/120 CM - for even tighter fine tuning). This is included with the Ultimate Kit.
* DO NOT PROGRAM THE CR3 PRO IT IS PRE-PROGRAMMED! - THIS OPTION IS AVAILABLE ONLY IF AN UPDATED FIRMWARE IS EVER RELEASED.
Perfect for increasing RGH / R-JTAG boot times. Used with CR3 Lite, CR3 Pro, R-JTAG, DGX & RGX dev boards.
Quality ceramic coating guarantees high moisture resistance and a wide operating temperature range. Operating tolerance ± 10%.
0.03nF / 30pF Rating.
The Datawrite 1.4GB 2x Mini DVD-RW (10 Pack) media is an excellent recordable blank media option to accompany your DVD camcorder. In addition to being able to assist your camcorder to create quality video recordings, these mini DVD-RW’s are also capable of being read by most DVD drives that have the appropriate slot for a mini DVD. This allows you to access, edit, and archive your digital video or even photos on the disc. At CK3, we have this Datawrite product on sale for an inexpensive cost.
Each of the Datawrite 1.4GB 2x Mini DVD-RW media products consists of a 10-pack cake box. Within the box are mini DVD-RW discs – a DVD of the “-RW” format means it is capable of being rewritten recording after recording, which is perfect for someone looking to record videos frequently without the need of keeping them in the long run. Moreover, these mini DVD-RW’s come with a storage capacity of 1.4GB, which interprets as about 30 minutes of DVD-quality video content.